Request a copy of RD-5R firmware for hotspot support
Re: Request a copy of RD-5R firmware for hotspot support
Thanks for the answer. I use this program for the first time. I'm not sure if I'm doing everything right. I have a white screen without changing the source code.I choose .project then compile and export the file then flash it via cps and white screen. It's sad I've been struggling with this for the second evening.I try with these sources 20240908 for RD5R
Re: Request a copy of RD-5R firmware for hotspot support
And it's not possible to have the hotspot working on a RD5R, as the USB is interrupted while transmitting, hence MMDVMHost is hanging.
Re: Request a copy of RD-5R firmware for hotspot support
I already told people multiple times that we know this doesn't work, but they don't seem to believe us.
E.g. viewtopic.php?f=9&t=3804#p29655
Re: Request a copy of RD-5R firmware for hotspot support
I figured out how to compile everything is ok. Now I need to figure out how to enable access point mode. Where can I enable it??
Re: Request a copy of RD-5R firmware for hotspot support
Thank you. I assembled and flashed RD5R with access point mode. DeepSeek did everything.
Re: Request a copy of RD-5R firmware for hotspot support
Hello everyone. Unstable operation of the access point on the RD-5R is not related to USB interference. It is related to a power supply sag during transmission. I tried connecting an external power supply. At 9 volts, 1.5 amps and a power of 250 mW, everything has been working stably for three hours. I do not claim that I have found a solution, but for now it works. From the battery, the port fails depending on the battery charge.
Re: Request a copy of RD-5R firmware for hotspot support
9V is much higher than the normal maximum voltage from the batteries, i.e max voltage when fully charged is usually 8.2VUR6LRD wrote: ↑Sun May 18, 2025 10:14 pmHello everyone. Unstable operation of the access point on the RD-5R is not related to USB interference. It is related to a power supply sag during transmission. I tried connecting an external power supply. At 9 volts, 1.5 amps and a power of 250 mW, everything has been working stably for three hours. I do not claim that I have found a solution, but for now it works. From the battery, the port fails depending on the battery charge.
Using 9V will cause the internal 5V and 3.3V voltage regulators to generate more heat than they are designed to dissipate.
Did you try using 8V or less, which is the normal operating voltage from batteries.?
Does it work at higher power levels using the external PSU?
Did you measure the Tx power ? i.e The calibration data in the RD5R is not normally accurate and your output power may be higher or lower than this value. i.e possibly much lower
Also. Is the 250mW setting the maximum stable power even when suppied from an external PSU?
Overall, it still appears that Hotspot mode is not stable on the RD5R in its normal operating configuation.
Re: Request a copy of RD-5R firmware for hotspot support
Hello. At 7 volts, the USB connection drops out during transmission at 8 volts randomly, maybe 1 minute maybe 10 minutes. At 9 volts, the point worked for 4 hours yesterday. Today I will turn it on for the whole day and test it. The power at 9 volts does not increase significantly. At 250 mW, I did not try more. But I tried to irradiate with another station turned on at 5 watts, the connection was stable.
R???????? ?? ????????? 250 ??? ???????????? ?????????? ????????? ????e: Request a copy of RD-5R firmware for hotspot sup
250 mW I think is not the limit. RD-5R has a problem with the sound of a motor boat in the DMR, it manifests itself at maximum power. It is necessary to disassemble and measure which stabilizer sags during transmission. I think this is the problem of this radio. Users without experience in radio electronics should not install firmware with an access point. I think I will conduct an experiment in the next few days and will report the result.