Baofeng DM-1701 programming cable help

YO2UKI
Posts: 11
Joined: Sun Oct 27, 2024 4:02 pm

Baofeng DM-1701 programming cable help

Post by YO2UKI » Wed Nov 06, 2024 6:20 pm

Hello, YO2UKI here!

I got a Baofeng DM-1701 from Aliexpress, and unfortunately it came with the wrong programming cable (it came with the classic UV-5R cable). I found one in my country, but I'm not sure if it will work. It's very similar in the photo with the one I think will work.
The cable is for "Anytone D868/878". Can anyone tell me if it would work? I can also send the link to the website if you want more information that I can't provide.

Thanks in advance!

SA0BUX
Posts: 873
Joined: Tue Jul 05, 2022 8:50 am
Location: JO99ah, Stockholm, Sweden
Contact:

Re: Baofeng DM-1701 programming cable help

Post by SA0BUX » Wed Nov 06, 2024 6:30 pm

The Anytone 878 cable has Data+ and Data- swapped compared to the DM-1701 cable.
DM-1701_RT84_Cable.jpg
DM-1701_RT84_Cable.jpg (53.42 KiB) Viewed 7271 times
RT3S_MD-UV380_GD77_cable_1.jpg
RT3S_MD-UV380_GD77_cable_1.jpg (78.51 KiB) Viewed 7271 times

YO2UKI
Posts: 11
Joined: Sun Oct 27, 2024 4:02 pm

Re: Baofeng DM-1701 programming cable help

Post by YO2UKI » Wed Nov 06, 2024 6:38 pm

And what's a reliable source to buy a DM-1701 cable from? Because I'm not sure that ordering one from China is the right choice since they sent me a wrong one in the first place.

SA0BUX
Posts: 873
Joined: Tue Jul 05, 2022 8:50 am
Location: JO99ah, Stockholm, Sweden
Contact:

Re: Baofeng DM-1701 programming cable help

Post by SA0BUX » Wed Nov 06, 2024 7:23 pm

YO2UKI wrote: ↑
Wed Nov 06, 2024 6:38 pm
And what's a reliable source to buy a DM-1701 cable from? Because I'm not sure that ordering one from China is the right choice since they sent me a wrong one in the first place.
Does it look similar to this ?
Capture.JPG
Capture.JPG (60.14 KiB) Viewed 7255 times
I think there is a little circuit board in the USB end with a FTDI serial interface or similar ?

Maybe you can remove the circuit board and connect the signals correct according to my first picture ?
Or cut the cable and connect it to some other old USB cable.

Or try amazon , I see that amazon.de has some cables that look ok and they deliver to Romania.

https://www.amazon.de/s?k=dm-1701+cable ... nb_sb_noss

VK3KYY
Posts: 8682
Joined: Sat Nov 16, 2019 3:25 am
Location: Melbourne, Australia

Re: Baofeng DM-1701 programming cable help

Post by VK3KYY » Wed Nov 06, 2024 7:24 pm

YO2UKI wrote: ↑
Wed Nov 06, 2024 6:38 pm
And what's a reliable source to buy a DM-1701 cable from? Because I'm not sure that ordering one from China is the right choice since they sent me a wrong one in the first place.
It will be cheaper and quicker to make a cable

Just buy a 3.5mm and 2.5mm plugs, and find any USB cable that's not only for charging, then cut the cable and solder on the plugs

YO2UKI
Posts: 11
Joined: Sun Oct 27, 2024 4:02 pm

Re: Baofeng DM-1701 programming cable help

Post by YO2UKI » Wed Nov 06, 2024 8:27 pm

SA0BUX wrote: ↑
Wed Nov 06, 2024 7:23 pm
YO2UKI wrote: ↑
Wed Nov 06, 2024 6:38 pm
And what's a reliable source to buy a DM-1701 cable from? Because I'm not sure that ordering one from China is the right choice since they sent me a wrong one in the first place.
Does it look similar to this ?
Capture.JPG

I think there is a little circuit board in the USB end with a FTDI serial interface or similar ?

Maybe you can remove the circuit board and connect the signals correct according to my first picture ?
Or cut the cable and connect it to some other old USB cable.

Or try amazon , I see that amazon.de has some cables that look ok and they deliver to Romania.

https://www.amazon.de/s?k=dm-1701+cable ... nb_sb_noss
Yes, it's very similar to that photo. I will try opening one up and seeing if I can solder it directly inside.

VK3KYY
Posts: 8682
Joined: Sat Nov 16, 2019 3:25 am
Location: Melbourne, Australia

Re: Baofeng DM-1701 programming cable help

Post by VK3KYY » Wed Nov 06, 2024 9:07 pm

If you can find a cable for a TYT radio e.g. UV380 or MD380 or a GD77 , you can open the plug and swap the data+ and data- wires

Or if you can find a Baofeng RD-5R / DM-5R they will work with no modifications

If the 'plug' has any chips in it, then its no good, you won't be able to modify it.

SA0BUX
Posts: 873
Joined: Tue Jul 05, 2022 8:50 am
Location: JO99ah, Stockholm, Sweden
Contact:

Re: Baofeng DM-1701 programming cable help

Post by SA0BUX » Thu Nov 07, 2024 2:22 am

YO2UKI wrote: ↑
Wed Nov 06, 2024 8:27 pm
SA0BUX wrote: ↑
Wed Nov 06, 2024 7:23 pm
YO2UKI wrote: ↑
Wed Nov 06, 2024 6:38 pm
And what's a reliable source to buy a DM-1701 cable from? Because I'm not sure that ordering one from China is the right choice since they sent me a wrong one in the first place.
Does it look similar to this ?
Capture.JPG

I think there is a little circuit board in the USB end with a FTDI serial interface or similar ?

Maybe you can remove the circuit board and connect the signals correct according to my first picture ?
Or cut the cable and connect it to some other old USB cable.

Or try amazon , I see that amazon.de has some cables that look ok and they deliver to Romania.

https://www.amazon.de/s?k=dm-1701+cable ... nb_sb_noss
Yes, it's very similar to that photo. I will try opening one up and seeing if I can solder it directly inside.
Otherwise I have ordered a cheap one via amazon.se that should arrive to me shortly.

I can send it to you as an "Elmer gift" after I verified that it works on Dm-1701 , my email is on qrz.com

/SA0BUX

YO2UKI
Posts: 11
Joined: Sun Oct 27, 2024 4:02 pm

Re: Baofeng DM-1701 programming cable help

Post by YO2UKI » Thu Nov 07, 2024 3:19 pm

Thanks everyone! I made my own cable until a new one arrives. However, now I have a new problem. It doesn't recognize the USB, no matter what I do (the drivers are installed). Is there any way to fix this or to see if it's my mistake?
Screenshot_510.png
Screenshot_510.png (7.84 KiB) Viewed 7156 times

SA0BUX
Posts: 873
Joined: Tue Jul 05, 2022 8:50 am
Location: JO99ah, Stockholm, Sweden
Contact:

Re: Baofeng DM-1701 programming cable help

Post by SA0BUX » Thu Nov 07, 2024 3:43 pm

YO2UKI wrote: ↑
Thu Nov 07, 2024 3:19 pm
Thanks everyone! I made my own cable until a new one arrives. However, now I have a new problem. It doesn't recognize the USB, no matter what I do (the drivers are installed). Is there any way to fix this or to see if it's my mistake? Screenshot_510.png
What windows version?

What DFU driver version?

Here's the the latest drivers from STM

downloads/drivers/Dfuse_3.0.6_drivers.zip