Page 2 of 3
Re: TS filter timer not working properly
Posted: Sun Nov 14, 2021 8:29 pm
by UA0LMC
No, initially there is no repeater activity for more than filter_time seconds. Then TS1 is active. Then I shortly press SK2 to switch to active TG from TS1. But instead I lose audio from that TG for filter_time seconds. If i'll transmit to TS2 from another radio within filter_time seconds after pressing SK2 - I'll hear myself, not TS1.
Re: TS filter timer not working properly
Posted: Sun Nov 14, 2021 8:39 pm
by F1RMB
Then, if you wait that filter time timeouts, it switches to TS1
Re: TS filter timer not working properly
Posted: Mon Nov 15, 2021 7:04 am
by UA0LMC
F1RMB wrote: ↑Sun Nov 14, 2021 8:39 pm
Then, if you wait that filter time timeouts, it switches to TS1
Yes, if I wait for filter_timeout - it monitors both TS then, and eventually receives TS1. Also if I press PTT within filter_timeout seconds after pressing SK2 - it transmits to TS1, but still receives TS2.
In other words, before SK2 was pressed - TX TS2, RX TS1. Right after SK2 was pressed - TX TS1, RX TS2 for filter_timeout seconds.
On the stable version when radio receives TS1 - I press SK2 and radio continues to receive TS1 and switches to active TG in TS1 so I could answer a call, so TX TS2, RX TS1 -> I press SK2 -> TX TS1, RX TS1.
Re: TS filter timer not working properly
Posted: Mon Nov 15, 2021 7:13 am
by F1RMB
UA0LMC wrote: ↑Mon Nov 15, 2021 7:04 am
F1RMB wrote: ↑Sun Nov 14, 2021 8:39 pm
Then, if you wait that filter time timeouts, it switches to TS1
TX TS2, RX TS1.
Right after SK2 was pressed - TX TS1, RX TS2 for filter_timeout seconds.
No, once you transmit on a given TS, it will stay on that TS for filter time seconds (And I just checked that, it's still working as expected).
Few beta back, that was broken.
Just to avoid confusion:
- the displayed TS in non-monitor mode is the TS you transmit on.
- In monitor mode, the displayed TS is the currently received one.
Re: TS filter timer not working properly
Posted: Mon Nov 15, 2021 7:30 am
by UA0LMC
F1RMB wrote: ↑Mon Nov 15, 2021 7:13 am
No, once you transmit on a given TS, it will stay on that TS for filter time seconds (And I just checked that, it's still working as expected).
Few beta back, that was broken.
Then something wrong with my radio because it works just as I described above. Just checked it again. Will try to find out the reason.
F1RMB wrote: ↑Mon Nov 15, 2021 7:13 am
Just to avoid confusion:
- the displayed TS in non-monitor mode is the TS you transmit on.
- In monitor mode, the displayed TS is the currently received one.
I don't use monitor mode - only TS filter off. Also I know which TG is in which TS on the repeater - so I omitted TG numbers in description, but it corresponds to TS in each case, working or non-working.
BTW, when I do a short press SK2 - it shows TS1, then a long press SK2 - it shows TS2. The problem is TS1 is the only active on repeater during the test.
Re: TS filter timer not working properly
Posted: Mon Nov 15, 2021 7:35 am
by F1RMB
UA0LMC wrote: ↑Mon Nov 15, 2021 7:30 am
F1RMB wrote: ↑Mon Nov 15, 2021 7:13 am
No, once you transmit on a given TS, it will stay on that TS for filter time seconds (And I just checked that, it's still working as expected).
Few beta back, that was broken.
Then something wrong with my radio because it works just as I described above. Just checked it again. Will try to find out the reason.
F1RMB wrote: ↑Mon Nov 15, 2021 7:13 am
Just to avoid confusion:
- the displayed TS in non-monitor mode is the TS you transmit on.
- In monitor mode, the displayed TS is the currently received one.
I don't use monitor mode - only TS filter off. Also I know which TG is in which TS on the repeater - so I omitted TG numbers in description, but it corresponds to TS in each case, working or non-working.
You're using monitor mode (SK2 long press), as you reported here.
What Filter time value is set on your transceiver ?
Re: TS filter timer not working properly
Posted: Mon Nov 15, 2021 7:42 am
by UA0LMC
F1RMB wrote: ↑Mon Nov 15, 2021 7:35 am
You're using monitor mode (SK2 long press), as you reported here.
I'm not. I do only a short SK2 press to switch to active TG - then the problem happens.
F1RMB wrote: ↑Mon Nov 15, 2021 7:35 am
What Filter time value is set on your transceiver ?
Filter time is 15s. Tried to change it back to default 10s - no change. And I performed an SK2+orange+power reset before.
When I do a short press SK2 - it shows TS1. Right after that I tried to do a long SK2 press - and it shows TS2. The problem is TS1 is the only active on repeater during the test.
Re: TS filter timer not working properly
Posted: Mon Nov 15, 2021 7:44 am
by F1RMB
UA0LMC wrote: ↑Mon Nov 15, 2021 7:42 am
I'm not. I do only a short SK2 press to switch to active TG - then the problem happens.
Oh, okay. Now I see the problem.
Re: TS filter timer not working properly
Posted: Mon Nov 15, 2021 7:49 am
by UA0LMC
F1RMB wrote: ↑Mon Nov 15, 2021 7:44 am
Oh, okay. Now I see the problem.
Can you reproduce it now on your radio?
Re: TS filter timer not working properly
Posted: Mon Nov 15, 2021 7:57 am
by F1RMB
UA0LMC wrote: ↑Mon Nov 15, 2021 7:49 am
F1RMB wrote: ↑Mon Nov 15, 2021 7:44 am
Oh, okay. Now I see the problem.
Can you reproduce it now on your radio?
Yes I can.