Page 3 of 3
Re: Stable release (2023 03 04)
Posted: Tue Aug 08, 2023 10:33 pm
by iz5wga
it's not the same cable, it's just a stright kenwood usb cable with no UART chip. It's the one I used to connect it to the rpi pi-star.
But apparently it's not a cable problem... the radio just turns off unless I keep the volume knob near the "power off". If I increase the volume, it gets down. Keeping the volume knob as low as possibile before the turn-off "click" it works.
Maybe I'm just better buy a 1701 (everyone is ok right? No special version trouble)
Re: Stable release (2023 03 04)
Posted: Tue Aug 08, 2023 10:41 pm
by VK3KYY
AFIK there is only one hardware version for the DM1701
Re: Stable release (2023 03 04)
Posted: Fri Sep 01, 2023 11:34 pm
by AI5MU
I recently bought a DM-1801UV and can't enter firmware mode using the two side button procedure. Is there a new way of doing it or did Baofeng remove the capability?
Re: Stable release (2023 03 04)
Posted: Sat Sep 02, 2023 12:45 am
by VK3KYY
AI5MU wrote: ↑Fri Sep 01, 2023 11:34 pm
I recently bought a DM-1801UV and can't enter firmware mode using the two side button procedure. Is there a new way of doing it or did Baofeng remove the capability?
Never heard of a DM-1801UV
Baofeng replaced the old DM-1801 with a model called the DR-1801 which is completely different hardware inside the case, and is
not updateable
Are you sure you bought a
DM-1801UV and not a
DR-1801UV
SOLVED Re: Stable release (2023 03 04)
Posted: Fri Dec 29, 2023 3:03 pm
by KE8OQQ
I'm getting a "cant connect" error while trying to update my firmware. I'm not sure what the issue is bc the read and write is working fine.
current firmwear:
Built Jun 13 2021
e6e9ded
- Screenshot 2023-12-29 095804.png (82.81 KiB) Viewed 4913 times
UPDATE :
i for got to: Turn on your transceiver in bootloader mode (SK1 + SK2 + power on).
Re: SOLVED Re: Stable release (2023 03 04)
Posted: Fri Dec 29, 2023 4:28 pm
by F1RMB
KE8OQQ wrote: ↑Fri Dec 29, 2023 3:03 pm
I'm getting a "cant connect" error while trying to update my firmware. I'm not sure what the issue is bc the read and write is working fine.
current firmwear:
Built Jun 13 2021
e6e9ded
Screenshot 2023-12-29 095804.png
UPDATE :
i for got to: Turn on your transceiver in bootloader mode (SK1 + SK2 + power on).
viewforum.php?f=10
Re: Stable release (2023 03 04)
Posted: Thu Jan 18, 2024 2:03 pm
by BH1AYY
md760 Is it supported
Re: Stable release (2023 03 04)
Posted: Thu Jan 18, 2024 7:17 pm
by VK3KYY
BH1AYY wrote: ↑Thu Jan 18, 2024 2:03 pm
md760 Is it supported
Md760 = gd77
Re: Stable release (2023 03 04)
Posted: Fri Jan 19, 2024 3:32 am
by BH1AYY
Thank you very much！
Re: Stable release (2023 03 04)
Posted: Fri Jan 19, 2024 3:33 am
by BH1AYY
VK3KYY wrote: ↑Thu Jan 18, 2024 7:17 pm
BH1AYY wrote: ↑Thu Jan 18, 2024 2:03 pm
md760 Is it supported
Md760 = gd77
Thank you very much！