[Fixed] DMR Rx dropout
Re: DMR Rx Dropout
Anyone with the DMR Rx dropout
Can you change to using this version
https://opengd77.com/downloads/MDUV380/ ... 01196e4f59
Colin has discovered a clash between various parts of the firmware accessing the C6000 DMR chip, which is probably what has been causing a lot of the problems.
I have also changed all the interrupt signal priorities to make sure the CPU can instantly respond to the C6000 when there is a DMR Timeslot synchronisation trigger.
And I have also changed the ADC processing which samples the volume control and battery and VOX, so this is handled by Direct Memory Access in the processor, rather than software ADC sampling
Its possible that the ADC sample rate will need to be adjusted, as I reduced it from 1000 samples per second, which was much more than was necessary to around 50 samples per second. But possibly we should use 100 samples per second for the volume control.
Note. The volume control in this radio is unfortunately not direct hardware, and the CPU has to handle the changes to volume control
Also battery voltage display averaging may also need to be adjusted, and currently the displayed battery voltage will not change as quickly in response to changes to supply / battery voltage changes
Can you change to using this version
https://opengd77.com/downloads/MDUV380/ ... 01196e4f59
Colin has discovered a clash between various parts of the firmware accessing the C6000 DMR chip, which is probably what has been causing a lot of the problems.
I have also changed all the interrupt signal priorities to make sure the CPU can instantly respond to the C6000 when there is a DMR Timeslot synchronisation trigger.
And I have also changed the ADC processing which samples the volume control and battery and VOX, so this is handled by Direct Memory Access in the processor, rather than software ADC sampling
Its possible that the ADC sample rate will need to be adjusted, as I reduced it from 1000 samples per second, which was much more than was necessary to around 50 samples per second. But possibly we should use 100 samples per second for the volume control.
Note. The volume control in this radio is unfortunately not direct hardware, and the CPU has to handle the changes to volume control
Also battery voltage display averaging may also need to be adjusted, and currently the displayed battery voltage will not change as quickly in response to changes to supply / battery voltage changes
Re: DMR Rx Dropout
i will try it later today and report.
Re: DMR Rx Dropout
Hello.
1.The 96 MHz version worked well.
2.Installed version Sep 29, 2022 - works for 3 hours, there are no errors yet.
3. What processor frequency is used in version Sep 29, 2022?
1.The 96 MHz version worked well.
2.Installed version Sep 29, 2022 - works for 3 hours, there are no errors yet.
3. What processor frequency is used in version Sep 29, 2022?
Re: DMR Rx Dropout
Latest version is 96Mhz, becuase the CPU takes less current at 96Mhz and its not necessary to use the full processing power of the CPU
On the GD77, I think the default CPU clock frequency is even lower, but lower CPU clock frequencies cause display problems on the UV380 / RT3S
Re: DMR Rx Dropout
No RX dropouts since! The battery life also seems to have improved with this version.
Re: DMR Rx Dropout
Thanks
I've found some other problems with the processor clock speed setup, and have probably found the main cause of the dropout, which was not actually the clock speed.
However it needs more testing before I can post anything.
Re: DMR Rx Dropout
I've been using the 96 MHz version, and none of those cyclical drop outs. But over a couple days I've heard stations go to that underwater sound like we had in the early days of the GD-77 firmware, but only a couple times.
Re: DMR Rx Dropout
Thanks
We have discovered multiple problems related to the processor clock frequency, the flash memory latency settings, the Serial Peripheral Interface speed.
All of which affect DMR RX and Tx
Its going to take some time to resolve these problems.
Re: DMR Rx Dropout
Good evening,
I have installed the 96mhz version for 2 days and I have no problem of drop, bad modulation or low signal.
Great for my RT3S, everything is fine for me.
Thanks to the whole team for the great job
73 Fabio
IK2TIF
I have installed the 96mhz version for 2 days and I have no problem of drop, bad modulation or low signal.
Great for my RT3S, everything is fine for me.
Thanks to the whole team for the great job
73 Fabio
IK2TIF