MDUV 380 stuck in FW upgrade mode
MDUV 380 stuck in FW upgrade mode
Followed the instructions for openGD77 for my mduv380. At first i got this, (Open GD77 support), (Unhanded exception has occurred in your application)
So I tried again. This time it asked for a (code pin) tried one more time. Now its stuck in FW upgrade mode red/green flash. Tried loading code plug, to no avail. Tried going back to original FW, no good, stays in FW upgrade mode. Any help would be appreciated..Thanks
So I tried again. This time it asked for a (code pin) tried one more time. Now its stuck in FW upgrade mode red/green flash. Tried loading code plug, to no avail. Tried going back to original FW, no good, stays in FW upgrade mode. Any help would be appreciated..Thanks
Re: MDUV 380 stuck in FW upgrade mode
Jays3hds
Disconnect and connect the battery. Then try updating FW again. I had a similar hang, the cable was damaged.
Disconnect and connect the battery. Then try updating FW again. I had a similar hang, the cable was damaged.
Re: MDUV 380 stuck in FW upgrade mode
Well that got me out of FW upgrade mode., but now its asking for a 2 digit pin code. I have no idea what the pin code is.
Re: MDUV 380 stuck in FW upgrade mode
Can't seem to put picture here. Just a white screen with Pin Code on top, below is _ _ and bottom left it says OK, above green button. When I push OK (Green Button) nothing happens. When I shut radio off it says 73.
This link might work for picture:
https://scontent.fagc1-1.fna.fbcdn.net/ ... e=63A35F9A
This link might work for picture:
https://scontent.fagc1-1.fna.fbcdn.net/ ... e=63A35F9A
Re: MDUV 380 stuck in FW upgrade mode
With the OpenGD77CPS, press the button to make a new codeplug.Jays3hds wrote: ↑Sat Dec 17, 2022 9:22 pmCan't seem to put picture here. Just a white screen with Pin Code on top, below is _ _ and bottom left it says OK, above green button. When I push OK (Green Button) nothing happens. When I shut radio off it says 73.
This link might work for picture:
https://scontent.fagc1-1.fna.fbcdn.net/ ... e=63A35F9A
This only has 2 channels in it.
Load that codeplug into the radio.
Re: MDUV 380 stuck in FW upgrade mode
Just tried a new code plug from scratch, link to what I get:
https://scontent.fagc1-2.fna.fbcdn.net/ ... e=63A3CD8C
https://scontent.fagc1-2.fna.fbcdn.net/ ... e=63A3CD8C
Re: MDUV 380 stuck in FW upgrade mode
Did you load the comm driverJays3hds wrote: ↑Sat Dec 17, 2022 10:04 pmJust tried a new code plug from scratch, link to what I get:
https://scontent.fagc1-2.fna.fbcdn.net/ ... e=63A3CD8C
Is the OpenGD77 Com device show in the device manager
Press the Details button to show the details of the error.
Re: MDUV 380 stuck in FW upgrade mode
It is noticed that sometimes several CPS processes can be detected in the task Manager. At the same time, similar failures were observed. Changing the USB port also helps.Jays3hds wrote: ↑Sat Dec 17, 2022 10:04 pmJust tried a new code plug from scratch, link to what I get:
https://scontent.fagc1-2.fna.fbcdn.net/ ... e=63A3CD8C
1. Reinstall CPS.
2. Restart the PC.
3. Write codeplug by default.
Re: MDUV 380 stuck in FW upgrade mode
Thanks everybody for all your help. I have the radio working !!! Seems I had 2 devices on the same com port somehow. Now I can enjoy OpenGD77 on my MD-UV380. Thank you all again......